CID400 - Telephone Clock Radio With Caller ID
Quick Reference Guide


This guide tells you how to quickly install and operate your new Caller ID Telephone Clock Radio. For more detailed instructions, please refer to your Owner's Manual.

Important Notice
1. Before using the CID400, install one (1) 9Volt alkaline battery into the base.
    NOTE: The battery is only for backup power for the Caller ID memory and Clock functions in
    case of an AC power failure.
2. DO NOT CONNECT the line cord into the wall outlet until after the Caller ID setup is
    completed.

Installation

Coil Cord Connection
Insert coil cord into modular jack located on the bottom of the base. Connect the other end into the modular jack located on the handset.

Line Cord Connection
With a modular telephone system, connect the straight telephone line cord to the modular jack located on the bottom of the base. Insert the other end of the cord into a modular wall jack. Make sure all plugs snap firmly in place. If you have a four prong style jack, plug the line cord into a modular adapter and then into the jack. DO NOT CONNECT the line cord into the wall outlet until after the Caller ID setup is completed (See Setting up your CID400 to complete the Caller ID setup).


Battery Installation
Open the battery door by pulling back the latch. Insert one (1) 9Volt alkaline battery. Snap the battery door back into place.

Setting Up Your CID400
NOTE: DO NOT CONNECT the line cord into the wall outlet until after the Caller ID setup is completed.

Language Setup
1. Once the batteries are installed, the LCD shows 'ENTER LANGUAGE' followed by a choice
    of 3 languages (ENG = English, ESP = Spanish, FRA = French).
    NOTE: If your display does not appear this way or to reset your Caller ID, press and hold the
    Caller ID review up and down buttons for 4 seconds.

2. The 'ENG' will be blinking. Press the Caller ID review buttons up or down to select the
    desired language.
3. Press the 'ERASE' button to confirm your selection. The LCD will then show 'ENTER AREA
    CODE'.

Area Code Setup
1. The first digit of the area code on your LCD display will blink.
2. Press the Caller ID review buttons up or down to select the first digit of your area code.
3. Press the 'ERASE' button to confirm the first digit of your area code.
4. Repeat steps above until 3-digit area code is set.
5. Once you have setup your area code, the LCD then will show 'ENTER TIME DATE'.

Time Date Setup
1. The hour digits on the LCD display will blink.
2. Press the Caller ID review buttons up or down to select the correct hour digit.
3. Press the 'ERASE' button to confirm the hour digit.
4. Repeat steps above until correct time and date is set.
5. Once you have setup your time and date, the LCD will then display 'TOTAL: 00 NEW: 00',
    which means both the total call and new call counter are zero.

Clock Setup
1. Press and hold TIME and HOUR controls simultaneously. Release when correct hour is
    displayed.
2. Press and hold TIME and MINUTE controls simultaneously. Release when correct minutes
    are displayed.
    NOTE: Please be certain that the proper AM is displayed when setting the clock.

Alarm Setup
3. Press and hold ALARM and HOUR controls simultaneously. Release when correct hour is
    displayed.
4. Press and hold ALARM and MINUTE controls simultaneously. Release when correct
    minutes are displayed.
    NOTE: Please be certain that the proper AM is displayed when setting the clock.

Operation

Receiving a Call
When your phone rings, pick up the handset and use like any basic telephone. Hang up the handset to release the telephone line when conversation is completed.
NOTE: If your radio is on when your phone rings, the radio will mute when you lift the handset from the base. Once the handset is back on the base, the radio will resume playing.

Dialing a Call
NOTE: Before dialing, make sure the Tone/Pulse switch is correctly positioned for your type of service.
Pick up phone, listen for a dial tone, then press the keys for the number you want. Your Conairphone(tm) (in pulse setting) uses electronic pulses to stimulate dialing. You might hear pulsing for a second or two after the last button has been pressed.

Key Features

Last Number Redial
Your Conairphone™ remembers the last number dialed. If the number you dial is busy or not being answered, hang up. To automatically redial the last number, press the REDIAL button. NOTE: You can redial the same number as many times as needed. However, once you dial another number, the previous number is erased.

Ringer On/Off or Off/Low/High
Your Conairphone(tm) features a harmonic tone ringer. When you don't want to be disturbed, slide the switch to the "Off" position. You can still make outgoing calls without being disturbed by incoming calls. Some phones have a ringer that can be adjusted to a soft (low) or a loud (high) sound level.

Receiver Volume Control
This feature allows you to adjust your handset volume from normal to high, for a more comfortable listening level.

Mute
To talk to someone on your end of the phone without the caller hearing your conversation, press and hold the MUTE button. Release the MUTE button to return to your telephone conversation.

Flash Function
The FLASH button can be used to retrieve a new dial tone after ending a call.

NOTE: The FLASH button is also used with special telephone services such as call waiting and three party calling. Press the FLASH button briefly, release and perform the custom call procedure.

Trouble Shooting Guide

Problem: No dial tone
• Check all modular plugs to be sure they are firmly in place.
• Are the cords damaged in any way?
• Try another phone jack. If your Conairphone™ works on another jack, there may be a
   problem with your wiring.

Problem: I hear my phone dialing, but I can not get past the dial tone.
• Check the Tone/Pulse switch. If positioned in Tone (T) mode, switch to Pulse (P). You may
   have pulse dialing service.

Problem: Phone does not ring.
• Is the ringer switch set to the "Off" position?
• How many extensions are connected to your line? If more than five telephones are installed
   on the same line, you may need to contact your local telephone company to determine the
   maximum number of extensions for your calling area.

Problem: The sound volume is too low.
• Is another extension off hook? If so, hang up the extension.

Conairphone™ Consumer Hotline

Questions? Call the Conairphone™ Consumer Hotline, toll-free, 1-800-366-0937.
Hotline Hours: Monday-Friday 8:30 a.m. - 9:00 p.m. (EST)
Saturday 8:30 a.m. - 12:30 p.m. (EST)
7475 North Glen Harbor Blvd.
Glendale, AZ 85307